60 fault codes with plain-English explanations, severity ratings, DIY guidance, and repair cost estimates.
The fault code is already on your display
Note it down before pressing reset — resetting clears the code immediately. How to read fault codes →
Tap any card for details
Your boiler has detected an internal communication error and has safely shut itself down as a precaution.
Your boiler has failed to light the flame properly and has stopped attempting to heat your home or water for safety reasons.
Your boiler has detected a false flame signal, meaning the system thinks the burner is lit when it should be turned off.
Your boiler has detected that it is not receiving enough water flow to operate safely or effectively.
Your boiler has detected an issue related to the flow of water inside the unit, which has caused it to stop working to protect itself from potential overheating.
Your boiler has failed to ignite or has lost the flame during operation because it is not receiving a consistent supply of gas.
Your boiler has detected an issue with the air supply or exhaust ventilation that prevents it from firing up safely.
Your boiler has detected an issue with the sensors that monitor the water flow, which is preventing it from firing up correctly.
Your boiler has detected a problem with the internal fan that controls the airflow needed to operate safely.
Your boiler has detected an issue with the airflow or exhaust system, meaning it cannot operate safely and has shut itself down.
Your boiler has detected an issue with the air flowing through the flue system, causing it to shut down for safety.
Your boiler has detected an issue with the water pressure sensor, preventing it from knowing if there is enough water to safely heat your home.
Your boiler has detected an issue with the air flowing through the system, preventing it from starting safely.
Your boiler is experiencing a communication failure between the control panel and the main operating system preventing it from firing up correctly.
Your boiler has detected an issue with the air supply or exhaust ventilation system that prevents it from firing safely.
Your boiler has detected an issue with the sensor that tracks the flow of water, which is preventing the system from operating correctly.
Your boiler has detected an internal communication or control board error and has safely stopped operating.
Your boiler has detected an internal communication failure between its main control boards, which prevents it from operating correctly.
Your boiler has detected a communication error between its internal parts, meaning it has safely shut down to prevent incorrect operation.
Your boiler has temporarily stopped working because it cannot safely ignite or maintain a flame.
Your boiler has detected an issue with the internal air or exhaust system that is preventing it from operating safely.
Your boiler is having difficulty communicating with its internal control system, which has caused it to stop working to avoid potential damage.
Your boiler has detected an issue with the water flow or circulation sensor, which is preventing it from heating your home or water correctly.
Your boiler has detected a communication error between its main computer and the internal circuit board, which effectively shuts down the system to prevent incorrect operation.
Your boiler has detected that it is getting too hot and has automatically shut down to prevent damage to its internal parts.
Your boiler is failing to light the flame properly, so it has stopped trying to prevent gas from building up inside.
Your boiler is trying to start up for heating or hot water, but it is failing to light the gas flame after several tries.
Your boiler is trying to start up but is failing to catch a flame, meaning you currently have no heating or hot water.
Your boiler has detected dangerously high water temperatures inside the heat exchanger and has locked out for safety because it cannot reliably control or sense the overheating condition.
Your boiler has detected internal bubbling or a potential leak which could damage internal components.
Your boiler has detected that parts of its internal heating system have reached a temperature that is too high, so it has safely shut itself down as a precaution.
Your boiler has detected dangerously high water temperatures inside the heat exchanger and has shut down to prevent damage or overheating.
Your boiler is temporarily suspending operation because its internal temperature sensors are reading incorrect or conflicting water temperatures.
Your boiler has detected an issue with the internal fan that safely pushes out exhaust gases, meaning it has shut down to prevent any risk.
Your boiler has detected an issue with the internal fan, which safely pushes exhaust gases outside, so it has shut down to prevent any risk.
Your boiler is confused about how hot the internal water is getting, so it has paused working to keep you safe.
Your boiler is getting confused about how hot the water inside it is getting, so it has paused to keep things safe.
Your boiler has detected that the water flow pipes are connected in the wrong order or that the heat is moving in the wrong direction, causing the system to shut down to prevent damage.
Your boiler has temporarily stopped working because the water pressure inside the system has dropped too low.
Your boiler is struggling to monitor the water pressure in your heating system, so it has safely shut down to prevent potential damage.
Your boiler has detected that the water pressure inside the heating system is too high for it to operate safely.
Your boiler is struggling to accurately read the water pressure inside the system, which is preventing it from firing up safely.
Your boiler is temporarily stopping because it is detecting incorrect water temperature readings from its internal sensors.
Your boiler is temporarily locked out because it is detecting an issue with the internal water temperature readings.
Your boiler is struggling to accurately measure or regulate the flow of water inside the system, which is causing it to stop heating as a safety precaution.
Your boiler is currently unable to tell if water is moving through the system, so it has safely shut down to prevent damage.
Your boiler is struggling to detect the temperature of your hot water, so it has safely shut down to prevent incorrect water temperatures.
Your boiler is having trouble controlling the temperature of the water being sent to your radiators, causing it to shut down to prevent damage.
Your boiler is receiving an incorrect temperature reading from the hot water storage cylinder sensor, which usually indicates a loose connection or a faulty sensor.
Your boiler's main control computer is experiencing an internal electronic fault, preventing the system from operating correctly.
Your boiler’s internal computer has identified an error in how its internal configuration switches are set, meaning it cannot operate safely until these are corrected.
Your boiler's electronic control panel is experiencing a communication fault, which prevents the display from responding or controlling the unit properly.
Your boiler's computer memory has encountered a serious internal error and can no longer process instructions correctly, meaning the unit cannot operate.
Your boiler's internal clock has lost its settings, which usually means the system cannot keep time to manage your heating schedule correctly.
Your boiler's main computer control panel is failing to process instructions correctly, which has caused the system to stop operating for safety reasons.
Your boiler is struggling to read the temperature outside, which means it cannot automatically adjust your heating to compensate for the current weather.
Your boiler's main control panel is failing to communicate with the internal system, which will prevent your heating and hot water from working properly.
Your boiler is having trouble communicating with your wall-mounted thermostat or smart control system, which prevents it from knowing when to turn on your heating.
Your boiler has detected a minor internal software or communication glitch and needs to be restarted to clear the error.
Your boiler has detected that its internal settings do not match the type of gas being supplied to your home, preventing it from firing up safely.
Monthly cover means no unexpected bills when your boiler breaks down.
Affiliate links. We may earn a commission at no extra cost to you.
BoilerFaultCodes